Home

Digital Clamp Multimeters

Digital Voltmeter Modules

Cables, Probes, Bags

Fuses for Multimeters

Milliohmmeters

LCR Meters and Component Testers

Energy Meters

Insulation Meters

Earth Resistance Meters

Electrical Installation Safety Testers

Cables-Voltage-Phase Testers

Magnetic Field Detectors

Power Line Analyzers

Signal Generators

Digital Oscilloscopes

Environmental Measures

Thermometers and Sensors

IR Thermal Imaging Cameras

Hygrometers

Anemometers and Pressure Gauges

Phonometers

Luxmeters

Chemical-Physical Characteristics

Set of Measuring Instruments

Tripods

Carrying cases

Accessories

There are 6 products.

Sort by:

PeakTech 4200 - Clamp Adaptor AC for Multimeter, 200 A, 16 mm, with 4 mm Plugs

Clamp Adaptor AC for Multimeter, 200 A, 16 mm, with 4 mm Plugs This clamp adaptor is a transducer, which allows to measure electrical current AC by connection with a digital multimeter. When measuring current with this clamp adaptor, it is no need to break a circuit or to affect the insulation. This adaptor with a design of finger guard, ensures user operating under condition safe.

$17.25

PeakTech 4250 - Clamp Adaptor DC/AC for Multimeter, 60 A, 9 mm, with 4 mm Plugs

Clamp Adaptor DC/AC for Multimeter, 60 A, 9 mm, with 4 mm Plugs A Transducer which will allows your multimeter to measure electrical current up to 60 A AC or DC, with a frequency response up to 20 kHz. The extended measurement jaws allow performing measurements in a narrow space. When measuring DC current, a simple operating push button is designed for zero adjustment. The clamp adapter is applicable to leakage detection or monitoring. For conductor diameter up to 9 mm.

$57.41

PeakTech 4300 - Clamp Adaptor DC/AC for Multimeter, 1000 A, 57 mm, with 4 mm Plugs

Clamp Adaptor DC/AC for Multimeter, 1000 A, 57 mm, with 4 mm Plugs A transducer which, in connection with a multimeter, allows measurements up to 1000 A DC/AC with frequency up to 400 Hz. Current measurements using a clamp transducer do not cause circuit interruptions. The transducer clamp is equipped with a hand edge protection, which ensures safe work. Measurements can be performed on cables with a diameter up to 57 mm or on bars up to 70 mm x 18 mm. The output voltage is 1 mV / A (1000:1) with the multimeter's input impedance & gt; 1 MΩ.

$71.51

PeakTech 4205 - Flexible Current Clamp Adapter for Multimeter, 30-300-3000 A AC, 160 mm, with 4 mm Plug

Flexible Current Clamp Adapter for Multimeter, 30-300-3000 A AC, 160 mm, with 4 mm Plug This innovative current clamp, due to its flexible nature, can be coupled to both small diameter and large diameter cables, up to 160 mm. Using the slide switch, the measuring ranges of the current clamp can be set to 30 / 300 / 3000 A AC.

$75.85

PeakTech 8010 - Sound level Calibrator 94, 114 dB

Sound level Calibrator 94, 114 dB For sound level measurements in extreme conditions, at high altitudes or high demands on the accuracy of the measurement results, sound level meters should be checked prior to the measurement with a sound level calibrator. Also for calibration and verification of microphones in audio technology, you need a sound level calibrator, which is designed to produce several sound pressure levels at a fixed frequency characteristic. This calibrator has two switchable calibration steps. The level “94dB”, which corresponds to a sound pressure of 1 Pascal, and the step “114dB”, which corresponds to a sound pressure of 10 Pascal.

$139.99

PeakTech 3131 - Clamp Meter DC/AC, 3 ¾ digits 13mm, 300A 22mm, True RMS, Auto Ranging

Clamp Meter DC/AC, 3 ¾ digits 13mm, 300A 22mm, True RMS, Auto Ranging

$162.67